Gate Opener Kit

NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener

NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener
NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener
NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener
NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener
NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener
NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener

NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener   NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener

This is a conventional sliding gate operator, with brand-new design, brand-new clutch structure, fashionable exterior design and brand-new control technique, making the motor more humanistic. Furthermore, the integrated electromechanical design and the streamlined appearance also make our product look more fashionable and elegant.

Sliding Gate Operator (1) (Set) (110v). Internal Hex-angular Bolt (4) (PCs). Left Limit Iron (1) (PCs). Right Limit Iron (1) (PCs). 18ft of Steel or Nylon Rack (6 PCs) (Cus tomer Choice). Life-long repairing with charge offered. Wires control and remote control. Please leave us a message with your voltage requirement (110V or 220V), if no message is left we will send according to your country voltage. Please leave us a message with your rack requirement (if no message is left we will send Nylon Rack).

4.1 Integrated structure of the mechanic and electron. No need to install other controllers. 4.3 Automatically restraining when meets obstacle.

4.4 Crash proof and automatically restraining socket. 4.5 Crash proof (photocell). 4.6 Alarm light socket. 4.7 Line control and remote control are optional.

4.8 Intelligent automatic heating function. 4.9 Automatically increase the temperature when the temperature is below 0 degree. 5.1 Motor base and it's installation. Motor base installation: set the installation position of the base tray according to the size of the motor and the height of the installation position of the gear rack. Then Embed the bolts in advanced or use the expansion bolts to embed the base into the cement foundation.

If the gear rack has already been installed, fix the motor to the base and turn the clutch with the clutch key to the off position, then make the gear of the motor suit right to the gear rack, then the position of the base can be set. Take off the motor and fix the base. 1 Put the motor on the base, fix up the motor with hexangular screws. 2 Loosen the four screws on the outer shell and remove the shell. Connect the wire according to the electric diagram.

After debugging, install the shell and fix it with bolts. Make the gear of the gear rack towards the floor. Make the gear of the rack fit the gear of the motor.

Fasten the gear rack to the door with the screws. Push the gate and make it move the whole route. Fasten the gear to the gate after assuring that the gate run smoothly the whole route. Rack is usually installed piece after piece.

To avoid dithering or blocking, please adjust the gap of the gear rack. We suggest one way(refer to Fig-3): fix up the rack1 and rack2 after adjusting the two racks with the small adjusting rack. 5.4 Travel limit iron installation. After the gear racks are fixed, open the clutch device and make the motor in idling status. Put the motor onto the base tray. Adjust the gear of the motor and make it fit the racks of the door.

After fixing the motor by bolts, connect the power for it. Press the'close' button of the controller, the motor will work towards the closing direction in loosening status.

Move the gate to the end position of the closing gate by hands. When the gate completely closes, check whether the limit iron could touch the spring limit switch and make the motor stop.

If the limit iron can not touch the spring limit switch, loosen the screws of the limit iron and move the limit iron to the right position and fasten it. Adjust the position of it in the same way again.

5.5 Function of release. When the release is opened, we can push the gate by hands, when the release is closed, the gate can be opened or closed by electricity and stop automatically when meets the limit iron. 5.6 Installation of photocell. Loosen the screws and take off the water-proof cover. Put photocell signal wire and power wire through the hole of the base.

Fix the photocell base with screws to appointed position. Put on the top lid and fasten it with screws. (Notice: During the installation, do not take off the rubber ring).

6.1 The electric control panel is set inside the outer shell and installed together with the motor. 6.2 For the electric connection, please refer to the electric connection diagram.

Debugging and instruction of use. Check the electric connections to make sure that the wiring has been connected well. Turn the power on and make the motor run itself. Send an open signal, then observe whether the rotational direction of the gear is the same as the direction of opening the gate.

If not, send a stop signal to make the motor stop running, and then rotate the direction adjustment switch to adjust the running direction of the motor. Send an open signal again, make sure the rotation are of the same. Then send a stop signal to stop the motor. Adjust the closing direction in the same way.

Adjustment of the limit switch. Send an open signal, press the limit switch towards the direction of opening the gate, observe whether the motor is stopped and limited. If not, rotate the limit adjustment switch to adjust again to make sure the opening limit switch functions.

Then send a close signal, adjust the closing limit switch in the same way. Check whether the gate is fixed well. Rotate the key of the clutch to opening direction according to the tips on the cover of the lock. Move the gate back and forth through the route by hand to see if it runs well or blocked. If the gate not move freely, adjust the position of the motor or the rack until it runs freely.

Close the clutch, if the gate runs in the opening direction, it can not respond to the CLOSE command, but can respond to the STOP, OPEN and LIMIT CLOSING command. If the gate runs in the closing direction, it cannot respond to the OPEN, STOP, LIMIT CLOSING and LIMIT OPENING command, but the OPEN and LIMIT CLOSING direction light are on. Three means to your safety: loop detector, photocell, crash proof. When the gate is opening, these three functions can not be applied.

When the gate is closing and meets some obstacles, the direction lights of the opening and closing limit are on at the same time and then turn to opening limit. When the signal of the infrared photocell is cut, the gate will turn to the opening limit and open till the direction light of the opening limit is on all the. When there is a signal to the loop detector, the gate will open for 10 seconds and then close automatically. You can adjust the crash proof sensitivity on the control panel. Rotate the clockwise, the sensitivity will be higher.

Temperature control function, when the system detects that the ambient temperature is below 0 degrees, the motor will heat automatically. 1 After checking and debugging all the parts, fix up the motor shell, close the clutch and the cover of the lock hole. When the power is cut off, open the clutch. Then move the gate manually.

When the power is on, close the clutch and run it by electricity. 1 The antifreeze lubricant oil has been applied to the sliding gate operator.

There is no need to add the oil before using. 2 After using the sliding gate operator for one month, please check the antifreeze lubricant oil. If it needs to be changed, please change the oil with the same type. Then check the oil every year.

If the oil turns bad, change the oil with the same type. 3 After using the gate operator for some time, please check if any parts are loose. If they turn loose, please tighten them.

9.1 The motor runs but the sliding gate operator doesn't work. A: Check whether the clutch is closed.

9.2 The power indicator light doesn't flash and the key doesn't react. A: Check whether power is connected right. 9.3 The opening and closing limit can not work.

A: Check whether the limit adjustment switch is installed right. B: Check whether the limit iron is installed right. Adjust the position of the limit iron. 9.4 Crash proof is not effective. A: Check whether the connection of crash proof is correct. B: Check whether the photocell is installed right. C: Check whether the connection of the wire of the loop detector is right. 9.5 When the gate just close up, it turns to open. A: Check whether the voltage is normal. B: If the crash proof equipment is installed, please check whether it works well. 9.6 The remote control doesn't work. A: Check whether the battery is low. B: Check whether the code of the remote control is the same with the code of the control panel. If the remote controller or the radio emitter doesn't match the code of the control panel, please adjust the code of the control panel or the code of the remote control to make them match.

The code is in the back of the remote control or the radio emitter. Users can make the code according to the codes. The code is from left to right. The above stands for the 1, the middle stands for X, the bottom stands for O. The follow code is :01XX1X0X.

Open the back cover of the controller and take off the battery. You can see the code of the pad on the PCB. The code is from right to left. The first code is on the right. When the middle pad and the above pad are shorted, it stands for 0.

When the middle pad and bottom pad are shorted, it stands for 1. The follow code is: 01XX1X0X. 1 One year maintenance services provided free of charge. 2 Life-long repairing with charge offered.

The following situations are charge for repairing. 1 Broken by wrongly installed. 2 The supply power is not stable and over the specific voltage. Broken by not using the standard electricity power of the country. 3 The gate operator is broken by wrongly using.

4 The gate operator is broken by natural disaster. 6 Not within the service items. The upgrade and improvement of the product won' t be notified if there is any. 1 The working voltage is 10% of the rated voltage, use power regulator if in area of volatile supply voltage.

2 The gear modulus: M=4 Gear scalar: Z=15. Please use the correspondent rack. 3 The gate should be balance-able and level.

So the gear and rack can fix well. 4 The gap between gears should be figured right so the gate operator can move smoothly. 5 The rail should be embedded right.

The wheel of the gate should be right and installed well. These are key points for the gate running well. Adjust the bolts which can make the gate operator up or down to make the gear fit the rack well. Make sure that the gate can be moved by an adult when the clutch is opened.

6 Make sure the running direction of the gate operator. The limit iron should be fixed at the right position, otherwise limit doesn't work and then the motor will be stocked and out of control.

Please install leakage power switch on the main power. Please cut off the main power when connecting. Electric products should be grounded. High voltage is dangerous, if you are non-professionals, please do not dismantle and repair. The item "NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener" is in sale since Wednesday, August 23, 2017. This item is in the category "Home & Garden\Home Improvement\Building & Hardware\Garage Doors & Openers\Opener Systems". The seller is "gate-hardware-and-equipments" and is located in Opa-Locka, Florida.

This item can be shipped worldwide.

  • Horse Power: 1800KG/4000LBS
  • Smart Home Protocol: Optional
  • Model: PY1800 Kit 1
  • Maximum Door Weight: 1800KG/4000LBS
  • MPN: PY1800 Kit 1
  • Maximum Gate Weight: 1800KG/4000LBS
  • Custom Bundle: Yes
  • Maximum Door Size: 20 Meter or 65 feets
  • Maximum Gate Size: 20 Meter or 65 feets
  • Motor Loading Weight: 4000 lbs (1800 kgs)
  • Smart Home Compatibility: Optional
  • Brand: NSEE
  • Application: Commercial
  • Power Source: Electric
  • Type: Rack and Pinions Operator Slide Gate Door Opener
  • Bundle Description: 18ft of Steel or Nylon Rack (6 PCs) (Customer Choice).
  • Voltage: 110V/220V AC


NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener   NSEE PY1800-1 1800KG/4000LBS Rack and Pinions Operator Slide Gate Door Opener